List of component parts of AMAP-1 (AMAR-1) car washer

1. Load-bearing frame securing repeated transportation (1 pc.).2. Heat-insulated outer contour providing with heat-insulation when using the car washer by+ 30° С — 30° С temperature range.3. Entrance butterfly swinging heat-insulated gates with locks saving from unauthorized penetration inside the car washer (1 pc.).4. Exterior cladding - sandwich polymer-plated panels (colour  - for customers’ choice, standard being white).5. Interior cladding - sandwich wall panels (colour - for customers’ choice, standard being white).6. Outer advertising panel along the washer perimeter (without wraparound).7. Entrance gate trap (4 pcs.).8.Three-stage circulating water supply system with coagulation chamber, floater, fresh water contour and pumps keeping up constant pressure in the system (1 pc.) per two posts.

9. Control sensors of water level in tanks.

10. A tank of 80 l. capacity (for diesel fuel) (1 pc.).11. Supply-and-exhaust ventilation (1 pc.).12. Autonomous  ALTECO air heating system, 9 KW-powered(1 pc.).13.Daylight lamps protected against moisture.14.Electrical interconnections with moisture protection.15.High pressure pump (150 bar) produced in Germany for car wash (1pc.).16.Vacuum-cleaner for dry cleaning of the car interior (1 pc.).17. Compressor for blowing of locks etc., 50 liters capacity (1 pc.).

List of component parts of AMAP-2 car washer

1. Load-bearing frame securing repeated transportation (2 pcs.).2. Heat-insulated outer contour providing with heat insulation when using the car washer by+ 30° С — 30° С temperature range.3. Entrance butterfly swinging heat insulated gates with locks saving from unauthorized penetration inside the car washer (2 pcs.).4. Exterior cladding - sandwich polymer-plated panels (colour  - for customers’ choice, standard being white).5.. Interior cladding - sandwich wall panels (colour - for customers’ choice, standard being white).6. Outer advertising panel along the washer perimeter (without wraparound).7. Entrance gate trap (2 pcs.).8. Three-stage circulating water supply system with coagulation chamber, floater, fresh water contour and pumps keeping up constant pressure in the system (1 pc.) per two posts.9. Control sensors of water level in tanks.10. A tank of 80 l. capacity (for diesel fuel) (1 pc.).11. Supply-and-exhaust ventilation (2 psc.).12. Autonomous WEBASTO liquid heating system, 30 KW-powered (diesel) (1 pc.).13.Daylight lamps protected against moisture.14. Electrical interconnections with moisture protection.15. High pressure pump (150 bar) produced in Germany for car wash (2 pcs.).16. Vacuum-cleaner for dry cleaning of the car interior (2 pcs.).17. Compressor for blowing of locks etc., 50 liters capacity with air-supply device for two posts(1 pc.).

Requirements for washer installation and car placing

This car washer is a self-bearing nonseparable structure and mounted on any even flat place with no concrete filling.By mounting on  a parking bay you need only to make an even ground using 5/20 fraction. Altitude drop across the entire mounting ground shall not exceed 1-2 cm.By installation on existing asphalt or any on the solid ground the car washer is mounted on special building steel-work slips.Overall dimensions of the site for installation of the one-post car washer with a glance of driving into it as well as the place for it make up: width - 5 m., length - 12.5 m.To install  a two-post car washer you will need following ground dimensions: width - 10 m., length - 12.5 m. You need also to provide for:

-a small place prior to car washer entrance;.- a place for probable queue of cars.For the one-post car washer dimensions of pre-entrance place of 7 m. wide and 8 m. long are desirable.For the two-post car washer this place will be 14 m. wide and 8 m. long.Total minimal place area, taking into consideration parking for one post is 119 m2 .Total minimal place area, taking into consideration parking for two posts is 237 m2 .